knowsAbout

1.00

GAGlobal

Hover & click on the images for description

Description

Description:

Check if (and by how much) unit knows about target. If unit is vehicle, vehicle commander is considered.

Multiplayer:

Although the command works only properly if unit is local, target can be located on any computer of the network.

Groups:

Uncategorised

Syntax

Syntax:

Number = unit knowsAbout target

Parameters:

unit: Object, Group or Side

target: Object

Return Value:

Number (from 0 to 4)

Examples

Example 1:

_kv = _soldierOne knowsAbout _jeepOne;

Example 2:

_kv = (side player) knowsAbout _target;

Additional Information

See also:

nearTargetsrevealgetHideFromtargetKnowledgetargetsAggregatetargetsQuery

Notes

Report bugs on the Feedback Tracker and/or discuss them on the Arma Discord or on the Forums.
Only post proven facts here! Add Note

Notes

Posted on August 4, 2006 - 10:55

hardrock

Notes from before the conversion: With Resistance (1.91): No matter what class of unit the target is and no matter what the skill/class of the enemy AI, the magic 'knowsAbout' number is 0.105. With CWC (1.46): No matter what class of unit the target is and no matter what the skill/class of the enemy AI, the magic 'knowsAbout' number is 0.7. What this means is, the AI will not fire on an enemy soldier until his 'knowsAbout' level of that enemy has reached the 'magic number' or higher. This suggests that the knowsabout level must reach the magic threshold before a unit knows if another unit is an enemy or a friendly unit. Triggers and knowsabout level: "Detected by xxx" triggers also follow the above rules. For a detected trigger to be set off, the knowsAbout level must reach the magic number. Also... As soon as An AI unit gets hit with a bullet his knowsAbout level for the unit that shot him will instantly jump to 1.5, even if the shooter is 1000m away. Vice versa is also true. If An AI soldier's knowsAbout level for an enemy is 0.7 and the soldier fires and hits the enemy, his knowsAbout level about the enemy will instantly jump to 1.5. Some editors have found, whilst using this command over the years, that the following characteristics have cropped up: AI enemies have a very limited amount of peripheral vision, it's not nearly as good as a human player's. A target must be in front of the unit for him to be noticed, so if you sprint right behind an enemy, this value doesn't increase. Depending on the units skill level, it can take a little time for the unit to notice a target. So if you run right past a unit, this value might not increase. Bushes between the unit and the target seem to have little effect on this value, and trees definitely have no affect. You may be in a forest, and can't see the unit, but he can see you. MP Note knowsAbout returns a viable result only if left-hand parameter unit is local.

Posted on January 15, 2007

Ceeeb

In OFP v1.96, KnowsAbout return values range from 0 to 4.

All units in a group have equal knowsAbout for any given target. All units in a group always return knowsAbout 4 about each other. This suggests groups share a single knowledge base.

Without any contact with the target, the knowsAbout value decays at a linear rate so that it halves over 120 seconds. After this time is up knowsAbout drops instantly to 0.

If the distance between the all of unit's group and the target exceeds the viewdistance setting, knowsAbout instantly drops to 0. This is not changed by fog or daylight.

Note that in OFP unit see all the targets that his group members see. The data is processed between teammembers freely.

Bdfy

the magic 'knowsAbout' number is 0.105. It's not that simple.Maybe true for infantry but not all vehicles. "Reveal" command sets knowsAbout to 1, but planes still won't fire at soldiers on the ground. There's only one known way to pass through this - designate target with another fake infantry unit near the target. As soon as this fake unit see the target knowsAbout lifts up to 2.5-4 and even single enemy soldiers are attacked rom the air (of course if plane has suitable munition :))

Posted on July 05, 2009

MaestrO.fr

In ArmA (other not tested), KnowsAbout value will stay at its highest value during approximately 2-3 min and then reinitialized.

Posted on January 14, 2012

kju

Notes are for OA 1.60:

The KnowsAbout value drops immediately back to zero, if the distance between both units is larger than the local viewDistance value.

After 110 seconds without (visible?) contact, the KnowsAbout value drops to zero again. While it seemed to take longer the higher the KnowsAbout value is (at least for a value of 4 it took almost six minutes at one point), I was unable to reproduce/confirm that. It is 110 seconds no matter how high the KnowsAbout value it seems.

Posted on June 13, 2012

kju

By Suma (source):

All friendly units within a view distance to each unit [are revealed (to the player? or each friendly?)] on the mission start. The code is half broken, as it does not make the units known, it only sets the "accuracy" value for them. Note: This is not affecting enemy units at all.

Posted on March 27, 2013

helling3r

Arma-II OA (1.62.101.480 @ACE), tests with infantry:

It is still true, that the command returns values between 0 (lowest) and 4 (most). Freshly Spotted units will have at least 1.5, slowly decreasing when the target disappeared. The following Table shows my test results on a clear day at Takistan using the Vector. Please note that the returned values vary considerably depending on weather and time. Moonlight however seems to not have any considerable effect.

12:00, sunlight, clear sky Distance knowsAbout 1530 1.5 1370 1.5 1250 1.5 1135 1.5 1055 1.52 1022 1.64 990 1.74 833 2.5 720 3.37 600 3.81 505 3.86 400 3.92 380 4 365 4

21:00, bright half moon, clear sky Distance knowsAbout 285 1.5 120 1.5 88 1.89 75 2.3 61 3.9

23:00, pitch black, clear sky, NVG on Distance knowsAbout 600 1.5 487 1.5 390 1.5 289 2.22 278 2.4

Posted on May 31, 2014 - 16:51 (UTC)

Delta99 wiki

Can also use SIDE in place of UNIT. For example: EAST knowsAbout player;